You need to supply the username (in most cases it is admin), and the password. In our example, 192.168.1.2 is router IP.
You may refer to the manual of your router to know the default IP address) of the router on a web browser. You can access this interface by accessing the IP address (which by default will be 192.168.0.1 or 192.168.1.1 unless you have changed it. A Note About WebGUIĪlmost all modern routers can be configured via browser based web administration GUI. Use ifconfig -a command to find out interface names. Please note that interface name (br0) may be different on your router.
You’ll find your iPhone’s MAC address in the Wi-Fi Address. Open the Settings app and navigate to Settings > General > About and scroll to the network section of the page. Let’s look at the several ways to find the MAC address of an iPhone and iPad. RX bytes:9146189 (8.7 MiB) TX bytes:74456679 (71.0 MiB) Your router may require the device’s MAC address. TX packets:61329 errors:0 dropped:0 overruns:0 carrier:0 RX packets:48574 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Once logged in type the ifconfig command, enter: $ ssh output: Welcome to nixCraft Router! If router remote management is turned on, type the following command to login into router via telnet or ssh command (telnet command works under MS-Windows oses too): To find your routers IP address on a Mac, click the Apple icon in the top-left corner of your screen and select System Preferences. On most router remote management via telnet / ssh is off by default. In above example 00:08:5C:00:00:01 is MAC address for router. It is hardwired or hard-coded onto your computers network interface card (NIC) and is. Type the following command to find out your router MAC address. Send ICMP ECHO_REQUEST (ping request) to route IP 192.168.1.2, enter: If the hostname parameter is not used, all entries will be displayed. arp shows the entries of the specified hosts. For debugging purposes, the arp program also allows a complete dump of the ARP cache. The primary options are clearing an address mapping entry and manually setting up one. arp command manipulates the kernel’s ARP cache in various ways. In such cases, you may have to call them and ask them to "reprovision" your modem.You need to use the arp command (available on both Windows, Linux/Unixish systems). Note that this menu may not be available on all devices, or it may only be available to be provisioned by your ISP. This should let you enter your own MAC address, it is designed to clone the MAC address of your network card. You can find the WAN IP address of your router on the main status page which is displayed as soon as you. You already know the LAN side address is 192.168.1.1. Likewise there are separate IP addresses for the WAN side and the LAN side of your router. Find the correct menu to change your MAC address It is usually in "Setup > Advanced", you're looking for a menu called " MAC Address Clone". You can find these MAC addresses by going to: System Monitoring. Some of the most common IPs are: Motorola SB modems: 192.168.100.1 Other modems/routers: 192.168.1.1 You can also lookup the default IP and login information of your device in our hardware database. If you're connected to it, you can drop to command prompt and type: ipconfig (the IP address of your "Default Gateway" should be the router/modem's IP). You will have to find your router/modem's IP address. Get to the web admin interface of your device. Here are the necessary steps to change the MAC address on your device: 1.
Below is a general guideline on how to do so on many routers/gateways and ADSL/VoIP/cable modems. Sometimes it is necessary to change that id and use a particular MAC address to be able to connect to your ISP. It helps identify the device on the network. All network hardware is assigned a special unique identifier, the Media Access Control ( MAC) address during production by its manufacturer.